boatbuildlog

Jersey Girl · step

Interior & Cockpit

Bulkheads, seats, buoyancy, sole, storage.

Interior & Cockpit on every boat, not just the Jersey Girl →

1
Builders
32
Entries
n/a
Median hours

Houseboat update Part 2, Thursday, September 20, 2018 -- Speaking of drainage from the poop deck, what's to prevent water from running down into the cabin? I'm installing a raised sill with a saddle of white oak, a beautiful, tightly-grained, tough wood that I think will resist wear over the years. To prevent water from leaking across the saddle under the aft cabin door, I am angling the red cedar undersill down toward the stern, so any water will drip away from the cabin, not into it. To do that, I'm making a series of angled cuts, using a Japanese pull saw, then a hammer and chisel to knock...

Read in context →

Houseboat update, Friday, September 21, 2018 -- Jersey Girl's poop deck is virtually complete, now that I have installed a white oak door sill leading into the cabin below and just forward. What could be more natural than moving from the poop deck, which has nothing to do with poop, to the head, which does? In the second photo, you can see the framing in a compartment on the starboard side of the aft end of the cabin, which support a flat floor in the head. I don't know anyone who would relish a squat on the pot while sitting on a slope, which is the shape of the hull bottom. Flat and level is...

Read in context →

Houseboat update, Wednesday, October 10, 2018 – Disaster averted! Lesson possibly learned, again (or not). I had an Idea that it would be nice to have access to storage below the fore deck from the pilot’s position inside the cabin, so I made sure to plunge-cut an opening in the forward starboard bulkhead, literally years ago. I saved the cut-out wood to turn into a grain-matched door. I actually found that wood, from three years ago, in the dusty clutter of my shop. Feeling pretty puffed up, I turned that piece of wood into a beautiful door, and I was just about to attach it with a continuous...

Read in context →

Houseboat update, Tuesday, November 20, 2018 -- The California grands are visiting for the week, so a special tour of Jersey Girl was arranged. That's Noah at the helm, and Taylor with me in the cabin.

Read in context →

Houseboat update, Tuesday, April 30, 2019 -- First things first: after a night and morning of drenching rain, the lilacs are in full bloom. Nothing signifies springtime so much as the sweet aroma of these sadly short-lived flowers. And, yes, the rain also gave me an opportunity to brush up on my bailing skills. But to the main point at hand -- I am starting to fit the aft cabin bulkhead in the starboard side! I will finish cutting it today, but before I install it I will have to sand it and give it a couple of protective coats of epoxy on both sides. That will take at least two more days, prob...

Read in context →

Houseboat update, Wednesday, May 8, 2019 -- I have been spending the last several days machining four midship roof support posts, a difficult, complicated job; arduous both physically and mentally. When I am working with expensive material like cedar, I greatly prefer not to make mistakes. So it's measure two or three times, check for fit, take break, come back, check again, then cut. Still, I make mistakes that need adjustments, but none I can't recover from. I still have to cut the decorative chamfers into the visible corners of these posts, then sand them and seal them with several coats of...

Read in context →

Houseboat update, Part 2, Wednesday, May 8, 2019 -- Yippee, a break! FedEx just arrived with the two eyebrow windows I've decided to use in Jersey Girl's aft bulkhead, the ones overlooking the aft deck. So I get to do some challenging (but fun) work. First, I position the window where I think it should be, and trace a grease pencil line around it. Next, I use a circular saw to make a plunge cut along the line, leaving just a bit at each corner so the waste piece doesn't break loose in an uncontrolled way and splinter the surrounding wood. Plunge cuts require practice and concentration; plunge...

Read in context →

Houseboat update, Friday, May 10, 2019 -- As I mentioned in a previous post, the design I'm using for Jersey Girl calls for a forward cabin bulkhead sporting a sweet bay-window shape instead of being flat from one side to the other. I want to stick with that design. But that calls for some rather complicated shaping of the posts that form the framework as it transitions from the sides to the angled forward windows and meet at the door frame in the center of the forward bulkhead. As an example, the side posts need to be square to fasten into the hull and its below-deck framing, but twist abrupt...

Read in context →

Houseboat update, Wednesday, May 29, 2019 -- Jersey Girl now has her forward cabin framing complete. With thunderstorms in the forecast soon, it's time to wrap up for the day. Next, as soon as the weather gods smile upon me, is to go back aft and install the framing that will define the galley on the port side and the enclosed head on the starboard.

Read in context →

Houseboat update, Part 2, Tuesday, June 4, 2019 -- Yesterday, I permanently fastened the forward posts that will delineate the spaces to be occupied by Jersey Girl's head on the starboard side and the galley on the port. Today, I will concentrate on the arched roof supports over the posts I installed yesterday, as well as timbers that will form the framework for windows.

Read in context →

Houseboat update, Part 3, Tuesday, June 4, 2019 -- I have another set of three arched roof supports permanently fastened into place, and I have begun to make the first of six window framing spacers. It's the unfinished lighter-colored post in the foreground. Four of them will be the same 1 1/2 x 1 1/2 inch timber you see here, and two will be slightly wider. Together, they will allow me to mount four 24-inch-wide windows on each side of Jersey Girl. In addition, there will be three forward-facing windows, one of them in the forward cabin door. There will be a similar window in the aft cabin do...

Read in context →

Houseboat update, Thursday, June 6, 2019 -- Notches, notches and more notches. Even some of the notches have notches of their own. Today was a day of fitting the three-dimensional jigsaw puzzle of framing together, mostly using a mallet and chisel. Here you can see Jersey's Girl's starboard side framing for the four windows that will stretch along the full length of the main cabin. Tomorrow, I'll make a few final adjustments and permanently glue and screw them into place. I already have the timbers cut and shaped for the port side, so I'll get them permanently fastened as well. After that, it'...

Read in context →

Houseboat update, Saturday, June 15, 2019 -- Windows! Jersey Girl has windows, seven of them so far. I need to shim a frame to fit the last window on the port side. That should be done later today, then it is on to the roof. As an update to the update, I am thanking a crew of hearty volunteers from the Ethical Culture Society of Bergen County, who actually paid money (as part of a fund-raiser for the Society) to help me install these windows. I provided the lunch, we all had a great time, and the windows got where they needed to be in record time and in good order. And miracle of miracles, no...

Read in context →

Houseboat update, Thursday, August 1, 2019 -- After two weeks away from Jersey Girl for traipsing through Yosemite, I am back at work. The forward deck area is pretty much complete, but for the railing and other details to come later. The hatch covers are installed, and they fit perfectly. The forward-facing cabin windows are screwed and sealed in place. Tomorrow, I will work on filling the spaces above and below the windows.

Read in context →

Houseboat update, Tuesday, August 6, 2019 -- Jersey Girl is putting her best face forward. I've installed all the bead-board tongue-and-groove planks in her forward cabin bulkhead, leaving window trim and building the door for later. Tomorrow, weather permitting, I will get started on the roof. Good news: I've discovered that the same six-inch tongue-and-groove I used for the cabin will conform with the arc of the roof very nicely. This will save a lot of construction time, and it will look great from inside the cabin. Stay tuned.

Read in context →

Houseboat update, Wednesday, August 14, 2019 -- Roofing on Jersey Girl progresses. Here's a series of photos to give an idea of what the inside will look like, from the motor well aft to the bow, and up to the roof. First is where the outboard motor will be, followed by the aft deck (which will also serve as an outdoor covered solar heated shower stall). Next, the door into the aft of the cabin. On the port (left) side will be the galley, equipped with small versions of stove, sink and refrigerator. Across the center aisle is space reserved for a head, with composting toilet. Forward of the tw...

Read in context →

Houseboat update, Wednesday, September 4, 2019 – This morning, I started to sand down the fairing compound I applied to Jersey Girl’s roof yesterday. But I quickly learned that this stuff has to be bone dry to sand easily. The morning dew that collected on the roof overnight was enough to quickly turn sanding dust into a gummy mess. So I turned my attention to something else that’s been bugging me for some time, and worked on that until the sun dried out the roof. I started closing the open spaces between the sheer of the hull and the bottom window frames, using the same beaded tongue and groo...

Read in context →

Houseboat update, Sunday, September 22, 2019 – Now that the final finish coat has been applies to the central portion of Jersey Girl’s arched roof, I can turn my attention to the more easily reached “shoulders” – the two outboard sides of the roof. In preparation for that, though, I’ve decided to close in the sides of the cabin that will accommodate the head on the starboard side and the galley on the port. That’s because each of these beadboard outer walls will have windows, and I’ll need to install the dripcaps over those windows before the roofing overhangs make it difficult to do that. So,...

Read in context →

Houseboat update, Tuesday, September 24, 2019 -- Jersey Girl is really stylin' now. Here's the aft starboard corner of her cabin. Just forward of the beadboard bulkhead separating the cabin from the aft deck is the space for what I will call euphemistically the "Ship's Library." Or, possibly, the "Throne Chamber." Or, maybe both. Tomorrow, I will begin work on the roof over the starboard side.

Read in context →

Houseboat update, Saturday, October 19, 2019 – I have some progress to report in my drive to close Jersey Girl’s cabin before the cold winter weather sets in. Over the past few days, I have found time to work on the port side, closing up the spaces under the windows on the port side, and completing the outer walls at the aft quarter on the port side, the space where the galley will be, sometimes, a special challenge will pop up, requiring a little thought before a solution is reached. In this case, it just so happened that the tongue-and-groove beadboard I am using for siding [presented a groo...

Read in context →

Houseboat update, Monday, December 2, 2019 – Today, I got a start making the tilt-up awning-style windows to fit the openings in Jersey Girl’s port-side Galley and Starboard-side head. I started with inexpensive flush-mount transom windows that manufactured to non-opening fixed windows. But because I want these to open, I’m first making a wooden frame to mount them in, and then I’ll hinge the framed windows into the cabin wall openings. So far, I’ve managed to complete one of these windows, including the outer flange that I hope will keep the weather from intruding past the frame into the cab...

Read in context →

Houseboat update, Thursday, December 5, 2019 – I finished building Jersey Girl’s second aft side window today, the one that will be installed in the galley, on the port side. First, I temporarily screwed the manufactured transom window into the frame I had built earlier, so I could accurately cut and fit the four pieces that would comprise the flanges. Then I cut the flanges on the table saw, setting the blade angle at 15 degrees for the ends of the side pieces and using the dame angle to rip the top and bottom pieces, to create a natural run-off for any water that might want to find its way i...

Read in context →

Houseboat update, Saturday, December 7, 2019 – Today, I installed the clerestory awning window in the head area of Jersey Girl’s starboard side, and I declare it a total success! But it took many steps and a minor re-do to get there. First, I realized that the stainless steel piano hinges I am using have a thickness of 3/16-inch, determined by the centerline of the hinge, where the pin connects the two halves along the 24-inch length. So I had to shave a bit of wood off the top of the window frame to accommodate the hinge. Next, I centered the hinge along the top of the window opening, using t...

Read in context →

Houseboat update, Wednesday, December 24, 2019 -- First of all, Jersey Girl and I wish you a most joyous Christmas! It's fairly warm for a Christmas Eve in Northern New Jersey, so I'm squeezing in a little work and taking a bit of a chance squeezing out a little epoxy. Here, I've started preparing for the aft cabin door frame, gluing and screwing a few short tongue-and-groove pieces into place over the door opening. Even though epoxy needs a 60-degree minimum temperature to cure properly, I'm not terribly concerned. All the pieces, being screwed tight, aren't moving anywhere. Eventually, I tru...

Read in context →

Houseboat update, Saturday, December 28, 2019 -- Still blessed with warm end-of-December weather, I was able to install the head jamb and two side jambs of Jersey Girl's aft door frame today. The starboard jamb was the perfect 90-degree angle from the head jamb, but -- oh, no! -- the post forming the framing foundation for the port side jamb was simply not plumb. From top to bottom, it was off by a full 3/4 inch. I am not the perfectionist some people accuse me of being, and normally I might have been tempted to say, "screw it, function is more important than form, so let it be." But in this c...

Read in context →

Houseboat update, Wednesday, January 1, 2020 – First of all, Jersey Girl and I wish everyone a most happy New Year, with the sincere hope that we all may find happiness and health and deeply meaningful change during the year to come. The run of decent weather continues, so I spent a few hours today continuing to prepare a properly framed door opening in JG’s aft cabin bulkhead. You can see that the jambs are in place, and I’ve used a piece of 2-by cedar as a riser that will be under the sill, or saddle. The top of the riser is sloped downward toward the outside, so that any water running down...

Read in context →

Houseboat update, Thursday, January 2, 2020 – Today’s the day to cut a saddle from a 1 x 6-inch piece of white oak for Jersey Girl’s aft cabin door. It’s a little tricky, because the inside and outside edges must be cut on an angle so that they are vertical when the saddle is installed over the 11-degree slope of the framing underneath. Not only that, but the inside edge of the “ears” that wrap around the door jambs have to be cut at the same angle so they form a close fit. The major edges are no problem; I simply set the angle of the table saw blade and cut. And cutting the inside edge of one...

Read in context →

Houseboat update, Tuesday, January 7, 2020 – I started working on the construction of Jersey Girl’s aft cabin door today. I’ve decided to make a sandwich assembly, using a piece of half-inch marine plywood as a core, faced on both sides with the same pine beadboard I’ve used elsewhere in the cabin, but thickness-planed down to a half inch. That will give me a door 1 ½ inches thick, allowing plenty of wood for hinges and other necessary hardware. Ultimately, the door will have a somewhat smaller version of the same windows I’ve used elsewhere in the cabin, for a uniform look. One interesting pr...

Read in context →

Houseboat update, Friday, January 10, 2020 – Yesterday, I temporarily installed faux rails, deliberately cut a bit too long, on the plywood door shape that will ultimately be the inner core of Jersey Girl’s aft cabin door. Today, I temporarily position the door. First, I loosely place a quarter-inch strip of wood on the inner saddle, to serve as a spacer to make sure the door is positioned at the correct height and allow clearance at the bottom. Then, after measuring gaps on both sides of the door to make sure it is centered between the jambs, I temporarily screw the ends of the rails into the...

Read in context →

Houseboat update, Saturday, January 11, 2020 – Today, Jersey Girl’s aft cabin door starts to look more like a real door. I mill enough beadboard a half-inch, then cut everything to fit, screwing it all in place temporarily to make sure I’ve measured and cut correctly, Then, I remove all the pieces, making sure to mark them before reinstall them with thickened epoxy. I feel a little guilty about the pleasure I take in a 68-degree day on the eleventh day of January, but I’ll take it! Finally, as I close up shop for the day, I have finished the outside face of the door. I have to say, I’m pretty...

Read in context →

Houseboat update, Tuesday, January 14, 2020 -- Jersey Girl's aft cabin door is almost a perfect fit, and it looks good too, I think. Just a tiny bit of planing on the hinge side, which will be the port (left) side, and I will be ready to install the hinges and the locking hardware. Then, I will finish the door with a couple of sealing coats of epoxy, which will give it an amber color like the surrounding cabin bulkhead. Eventually, all this epoxied woodwork will be protected from UV of sunlight by multiple coats of marine varnish. On the inside, I elected to leave the plywood core showing, as...

Read in context →

Houseboat update, Thursday, January 16 -- Jersey Girl's aft cabin door is, if I may use the expression without intending any offense, well hung. It opens and closes freely, and with its opening, screened window in place, I think it looks pretty good. I still have a few details to attend to, which I will do tomorrow: I need to install the latch and deadbolt striker plates for the locks, then the door stop mouldings with weather seals, and finally the outside casings for a nice, finished appearance. Then, I'll go around to the forward end and do the same thing all over again.

Read in context →