More Photos
Runabout · modification
Usain Boat
1963 Belmont runabout 19'
More Photos
Steering Helm Upgrade As temperatures warmed up, the steering wheel became nearly impossible to turn due to a failed 20-year-old cable and helm. I replaced it with a SeaStar Teleflex (SSX17617) Tilt Xtreme NFB 16 ft Rotary Steering Cable & Helm Kit, which mated perfectly with the stock steering wheel. I decided not to activate the horn for now due to the difficulty of drilling through the dash for wiring, though the cable is routed if I decide to hook it up later. October & November Updates I refinished and reinstalled the engine cover with fresh paint and varnish, installed new Stewart-Warner gauges, and scored a great deal on original gas caps on eBay. During a test fire after rebuilding the carb, the battery went dead because the igniter wire had come loose at the starter. I also located the original stain formula: Bamboo Mahogany, which features a rich dark tint with subtle purple undertones. In November, I moved the Belmont to the school shop to work on it and use it as a project for virtual boat-building sessions on Wednesday nights. We lifted the hull off the trailer onto shop dollies and discovered significant damage on the sides behind the wheel wells. We prepped the area, laid down new fiberglass corners, and restored incredible strength to the structure. After it cured, I sanded it smooth and applied light layers of polyester fairing compound across the corners and bottom. Minor dings on the topsides were filled as well. December Stripping & Refinishing I stripped the hull sides using three generous coats of TotalBoat Stripper. The varnish lifted in about 15 minutes, while the underlying fiberglass resin required two coats and an overnight soak to dissolve. Areas that had never been exposed to sunlight remained very dark and required hand scraping and sanding down to bare wood. Because the mahogany veneer was paper-thin in places, it appeared this hull had been stripped at least once before. With the bare wood exposed, screw holes were filled with mahogany Famowood filler (or solid mahogany plugs where structural strength was needed). I applied Minwax Bombay Mahogany stain to recreate the original dark purple-tinted hue, followed by a heavy coat of penetrating sealer and 9 coats of clear marine varnish before dry sanding.
More Photos, start of engine repair
January – Summer 2021 With the bottom paint complete, I sanded the 9 coats of varnish with 400-grit sandpaper at low speed to flatten the surface. Working in a 55°F shop (below recommended application temperatures) created "micro-runs" that required careful leveling. I followed up with 600-grit paper and light coats of clear gloss varnish prior to final buffing. When COVID-19 restrictions closed the shop in February 2021, Usain Boat went into temporary storage. Once the school year wrapped up in summer 2021, I unpacked the Belmont to prepare for its maiden lake cruise. Unfortunately, things didn't go as planned: Upon launching, the hull began taking on water due to a missing drain plug. The engine struggled to turn over. Inspection revealed the cylinders were completely hydraulic-locked with water. I tore the engine down to the block and realized that flushing with a pressurized garden hose through log-style exhausts had back-fed water straight into the engine. (In the future, I will use a bucket-and-water-pump setup). While the engine was out, I honed the cylinders and installed new rings. The engine had previously been rebuilt .030" over and showed minimal wear. Light surface rust from the water incident was cleaned up using a 230-grit ball hone. Rebuilding was a blessing in disguise, as it allowed me to correct several minor assembly errors, including issues with the starter. Uncovering Engine Origins While sourcing a marine starter, I uncovered the engine's true origins: The block was painted red underneath, whereas Cadillac automotive engines were dark blue. Search results for the starter design repeatedly pointed to Crusader Marine Engines, which used red engine paint. The block serial numbers, head stamps, positive vacuum valve cover components, chrome valve covers, and marine attachments (Nicson exhaust, Cal Marine timing cover, Halibrand bellhousing) matched Crusader specifications for a 1962 390 crate engine. Crusader Marine Co. sold 390 Cadillac crate engines in the early 1960s, which aligns with Smitty Weaks' practice of sourcing whatever high-performance engines were available. RAM Engine in Spokane, WA had rebuilt this engine .030" over in the 1990s, leaving behind their distinctive shop markings. Gauge Salvage & 2023 Launch Prep The old automotive gauges were rusted, so I replaced them with period-correct marine units. I listed the old gauges on eBay expecting 20–30 each. Surprisingly, an old Stewart-Warner oil pressure gauge with the classic winged logo and curved glass sold for $420!
Nobody else here is logging a Runabout yet. See the boat.