boatbuildlog

Runabout · modification

Usain Boat

by Alan Wardsworth · Spokane Valley, Washington · Message Alan Wardsworth

1963 Belmont runabout 19'

Make a book Feed The whole log, 2 entries and every photo, laid out as a book to print, bind and keep.
23
Entries
200
Hours
n/a
Written up afterwards
437
Photos
Mar 2020
Started

See Trailer & Launching on other boats →

Trailer & Launching · other boats 10 h Link

By summer 2023, the boat was ready for a Show & Shine event. However, upon dropping it in the water, the shaft log leaked so severely that the bilge pump struggled to keep up. Shaft Log & Covering Board Repairs The original shaft log used 12 studs protruding through the keel. Rust and old bilge paint made them nearly impossible to remove; two snapped off and four were completely loose. Upon removal, I found the original sealant had degraded to powder. I cleaned the mating surfaces, coated a new rubber gasket with Boat Seal, and reinstalled it using larger-diameter stainless steel screws. Unfortunately, the center of the aluminum plate didn't clamp down evenly, causing another leak. I repaired the mounting holes using expanding epoxy and toothpicks, but hitting lake waves broke the bond again. Meanwhile, the gunwale covering boards (the upper edges of the hull where you rest your arm) were in rough shape from dock impacts and weathered repairs. Option 1: Router out the entire 6" x 20' board and replace it with solid mahogany. (Too time-consuming for this season). Option 2: Remove the old plywood planks. (Ken Johnson, who restored the boat in the 1990s, confirmed they were glued down with 3M 5200). Option 3: Strip and refinish. (Chemical stripper failed on the sun-baked 3 oz fiberglass layer, and 80-grit belt sanding bit too deep into the thin top mahogany ply). Option 4 (Selected): Belt-sand the surface flat, block-sand, and veneer over the existing covering boards with 1/45" mahogany veneer using urea-resin and contact adhesive. I prepped the surfaces, taped off the white deck accent line, and sourced veneer and glue from VeneerSupplies.com. Aft sections were glued with urea resin, weighted under 3/8" boards, and set up flat. Midship and windshield sections were pre-glued to prevent the dry plywood substrate from absorbing all the adhesive. Forward bow curves proved difficult to clamp. After failed attempts with urea resin and Titebond III, I stripped the forward section back down and used 3M Extreme Contact Cement. Using dowel rods to align the veneer before pressing down worked like a charm. To trim the outer edges without splitting the grain, I treated the veneer with Super Soft 2 veneer softener, trimmed it with a veneer knife, and block-sanded the edges smooth. To recreate the 1/4" white deck accent line, I built an adjustable 6" fence plate for my trim router and routed a clean new groove along the rail. Old offset grooves were filled with epoxy and repainted. I stained the new veneer, sealed it with penetrating epoxy, and built up 10 coats of TotalBoat Halcyon spar varnish, followed by 5 coats of TotalBoat High-Gloss Gleam (sanding every 5 coats).

1 Runabout: trailer & launching
2 Runabout: trailer & launching
3 Runabout: trailer & launching
4 Runabout: trailer & launching
5 Runabout: trailer & launching
6 Runabout: trailer & launching
7 Runabout: trailer & launching
8 Runabout: trailer & launching
9 Runabout: trailer & launching
10 Runabout: trailer & launching
11 Runabout: trailer & launching
12 Runabout: trailer & launching
13 Runabout: trailer & launching
14 Runabout: trailer & launching
15 Runabout: trailer & launching
16 Runabout: trailer & launching
17 Runabout: trailer & launching
18 Runabout: trailer & launching
19 Runabout: trailer & launching
20 Runabout: trailer & launching
21 Runabout: trailer & launching
22 Runabout: trailer & launching
23 Runabout: trailer & launching
24 Runabout: trailer & launching
Trailer & Launching · other boats 10 h Link

Final Photos

1 Runabout: trailer & launching
2 Runabout: trailer & launching
3 Runabout: trailer & launching
4 Runabout: trailer & launching
5 Runabout: trailer & launching
6 Runabout: trailer & launching

Nobody else here is logging a Runabout yet. See the boat.