boatbuildlog

Runabout · modification

Usain Boat

by Alan Wardsworth · Spokane Valley, Washington · Message Alan Wardsworth

1963 Belmont runabout 19'

Make a book Feed The whole log, 3 entries and every photo, laid out as a book to print, bind and keep.
23
Entries
200
Hours
n/a
Written up afterwards
437
Photos
Mar 2020
Started

See Engine & Propulsion on other boats →

Engine & Propulsion · other boats 10 h Link

Upgrades & Electronics The electrical wiring harness was in terrible shape; bending the wires caused the insulation to crack and flake off. I ordered new marine-grade wiring and cables, along with heat-shrink, waterproof connectors. I also ordered a couple of replacement gauges to match the original Stewart-Warner units. I completed the engine hatch modification by centering it in the opening and cutting it cleanly in half using a Bosch jigsaw with a new fine-tooth blade at 0°. I built support frames for both halves, then bored a 3/4" hole to accept a brass bushing, stainless steel bolt, and locking washers. The hardest part was leaving enough clearance without making the new vent stack excessively tall. I also won a set of 1968 Camaro hood vents on eBay that look like they were custom-made for this boat. For the finish, Kirby Paint Co. provided a paint match that was remarkably close (just slightly greener compared to the original yellow tint). I brushed it on using a foam brush; as it dried, it laid out smoothly and looked awesome. I'll give it a month to cure completely before buffing. Naming the Vessel According to the previous owners, there was a sister boat named ?. My wife made two things clear: she has to be able to drive the boat (meaning an adjustable throttle pedal), and the name must be changed from Floozy! Changing a vessel's name without consulting Poseidon risks invoking his wrath, so a proper purging ceremony is required to appease the sea gods and erase the old name from the Ledger of the Deep. For a new name, I came up with USAIN BOAT (a nod for the non-track-and-field folks to Usain Bolt, world record holder in the 100m and 200m). Or maybe CaddyDaddy?

1 Runabout: engine & propulsion
2 Runabout: engine & propulsion
3 Runabout: engine & propulsion
4 Runabout: engine & propulsion
5 Runabout: engine & propulsion
6 Runabout: engine & propulsion
7 Runabout: engine & propulsion
8 Runabout: engine & propulsion
9 Runabout: engine & propulsion
10 Runabout: engine & propulsion
11 Runabout: engine & propulsion
12 Runabout: engine & propulsion
13 Runabout: engine & propulsion
14 Runabout: engine & propulsion
15 Runabout: engine & propulsion
16 Runabout: engine & propulsion
17 Runabout: engine & propulsion
18 Runabout: engine & propulsion
19 Runabout: engine & propulsion
20 Runabout: engine & propulsion
21 Runabout: engine & propulsion
22 Runabout: engine & propulsion
23 Runabout: engine & propulsion
24 Runabout: engine & propulsion
Engine & Propulsion · other boats 10 h Link

More Photos, start of engine repair

1 Runabout: engine & propulsion
2 Runabout: engine & propulsion
3 Runabout: engine & propulsion
4 Runabout: engine & propulsion
5 Runabout: engine & propulsion
6 Runabout: engine & propulsion
7 Runabout: engine & propulsion
8 Runabout: engine & propulsion
9 Runabout: engine & propulsion
10 Runabout: engine & propulsion
11 Runabout: engine & propulsion
12 Runabout: engine & propulsion
13 Runabout: engine & propulsion
14 Runabout: engine & propulsion
15 Runabout: engine & propulsion
16 Runabout: engine & propulsion
17 Runabout: engine & propulsion
18 Runabout: engine & propulsion
19 Runabout: engine & propulsion
20 Runabout: engine & propulsion
21 Runabout: engine & propulsion
22 Runabout: engine & propulsion
23 Runabout: engine & propulsion
24 Runabout: engine & propulsion
Engine & Propulsion · other boats 10 h Link

January – Summer 2021 With the bottom paint complete, I sanded the 9 coats of varnish with 400-grit sandpaper at low speed to flatten the surface. Working in a 55°F shop (below recommended application temperatures) created "micro-runs" that required careful leveling. I followed up with 600-grit paper and light coats of clear gloss varnish prior to final buffing. When COVID-19 restrictions closed the shop in February 2021, Usain Boat went into temporary storage. Once the school year wrapped up in summer 2021, I unpacked the Belmont to prepare for its maiden lake cruise. Unfortunately, things didn't go as planned: Upon launching, the hull began taking on water due to a missing drain plug. The engine struggled to turn over. Inspection revealed the cylinders were completely hydraulic-locked with water. I tore the engine down to the block and realized that flushing with a pressurized garden hose through log-style exhausts had back-fed water straight into the engine. (In the future, I will use a bucket-and-water-pump setup). While the engine was out, I honed the cylinders and installed new rings. The engine had previously been rebuilt .030" over and showed minimal wear. Light surface rust from the water incident was cleaned up using a 230-grit ball hone. Rebuilding was a blessing in disguise, as it allowed me to correct several minor assembly errors, including issues with the starter. Uncovering Engine Origins While sourcing a marine starter, I uncovered the engine's true origins: The block was painted red underneath, whereas Cadillac automotive engines were dark blue. Search results for the starter design repeatedly pointed to Crusader Marine Engines, which used red engine paint. The block serial numbers, head stamps, positive vacuum valve cover components, chrome valve covers, and marine attachments (Nicson exhaust, Cal Marine timing cover, Halibrand bellhousing) matched Crusader specifications for a 1962 390 crate engine. Crusader Marine Co. sold 390 Cadillac crate engines in the early 1960s, which aligns with Smitty Weaks' practice of sourcing whatever high-performance engines were available. RAM Engine in Spokane, WA had rebuilt this engine .030" over in the 1990s, leaving behind their distinctive shop markings. Gauge Salvage & 2023 Launch Prep The old automotive gauges were rusted, so I replaced them with period-correct marine units. I listed the old gauges on eBay expecting 20–30 each. Surprisingly, an old Stewart-Warner oil pressure gauge with the classic winged logo and curved glass sold for $420!

1 Runabout: engine & propulsion
2 Runabout: engine & propulsion
3 Runabout: engine & propulsion
4 Runabout: engine & propulsion
5 Runabout: engine & propulsion
6 Runabout: engine & propulsion
7 Runabout: engine & propulsion
8 Runabout: engine & propulsion
9 Runabout: engine & propulsion
10 Runabout: engine & propulsion
11 Runabout: engine & propulsion
12 Runabout: engine & propulsion
13 Runabout: engine & propulsion
14 Runabout: engine & propulsion
15 Runabout: engine & propulsion
16 Runabout: engine & propulsion
17 Runabout: engine & propulsion
18 Runabout: engine & propulsion
19 Runabout: engine & propulsion
20 Runabout: engine & propulsion
21 Runabout: engine & propulsion
22 Runabout: engine & propulsion
23 Runabout: engine & propulsion
24 Runabout: engine & propulsion

Nobody else here is logging a Runabout yet. See the boat.