boatbuildlog

Runabout · modification

Usain Boat

by Alan Wardsworth · Spokane Valley, Washington · Message Alan Wardsworth

1963 Belmont runabout 19'

Make a book Feed The whole log, 12 entries and every photo, laid out as a book to print, bind and keep.
23
Entries
200
Hours
n/a
Written up afterwards
437
Photos
Mar 2020
Started

See Planning & Parts on other boats →

Planning & Parts · other boats 10 h Link

Fuel Tank Restoration The dual 24-gallon fuel tanks mounted behind the seats developed a strong gasoline odor caused by missing vent lines and unvented replacement gas caps. Additionally, the fuel sending unit gave erratic readings because the float had sprung a leak. I drained 30 gallons of fuel, removed the tanks, and had Carlson Sheet Metal MIG-weld proper vent fittings onto each tank. After pressure-testing, I treated the rusted bottom of one tank with POR-15 tank sealer. Unfortunately, the POR-15 failed to adhere properly to the existing interior lining and began peeling. I had to un-seam the top of the tank, scrape out the failed liner, wire-brush the rust, rivet the top back together, and resolder the seams. I installed a 5/8" fuel equalization crossover line between both tanks, replaced all fuel lines with USCG Type A1-15 hose, converted the carburetor to a properly vented marine setup, replaced the fuel line from the pump to the carb with a hardline, and grounded both tanks to meet USCG safety standards.

1 Runabout: planning & parts
2 Runabout: planning & parts
3 Runabout: planning & parts
4 Runabout: planning & parts
5 Runabout: planning & parts
6 Runabout: planning & parts
7 Runabout: planning & parts
8 Runabout: planning & parts
9 Runabout: planning & parts
10 Runabout: planning & parts
11 Runabout: planning & parts
12 Runabout: planning & parts
Planning & Parts · other boats 10 h Link

2024 Season Debut We kicked off 2024 addressing three final items: Fuel Tanks: Over-tightening hold-down straps had cracked the seam epoxy. I relieved strap tension, reinforced the corners with angle iron, and re-sealed them. Transom Leak: Delaminated transom plywood was prepped, saturated with penetrating epoxy, sealed, and fairing compound applied below the waterline. Carburetor: The old Edelbrock carb was gummed up from ethanol fuel. I replaced it with a new Edelbrock Marine 750 CFM carburetor. On the morning of August 12, 2024, we launched Usain Boat. Aside from waking up a few cranky lakefront neighbors, she ran and performed beautifully!

1 Runabout: planning & parts
2 Runabout: planning & parts
3 Runabout: planning & parts
4 Runabout: planning & parts
5 Runabout: planning & parts
6 Runabout: planning & parts
7 Runabout: planning & parts
8 Runabout: planning & parts
9 Runabout: planning & parts
10 Runabout: planning & parts
11 Runabout: planning & parts
12 Runabout: planning & parts
13 Runabout: planning & parts
14 Runabout: planning & parts
15 Runabout: planning & parts
16 Runabout: planning & parts
17 Runabout: planning & parts
18 Runabout: planning & parts
19 Runabout: planning & parts
20 Runabout: planning & parts
21 Runabout: planning & parts
22 Runabout: planning & parts
23 Runabout: planning & parts
24 Runabout: planning & parts

Nobody else here is logging a Runabout yet. See the boat.