boatbuildlog

Northeaster Dory · new build

Northeaster Dory to be assembled in Cologne Germany

It is the first boat I build. I‘ll do it in my single garage and partly in my cellar.

Make a book Feed The whole log, 4 entries and every photo, laid out as a book to print, bind and keep.
23
Entries
121
Hours
32
Days elapsed
65
Photos
Oct 2026
Started
Watch the 30 second boat build video

The film on its own page

See Glassing & Epoxy on other boats →

Glassing & Epoxy · compare · other boats 5.5 h Link

Troubleshooting and a bit more

I removed the fillets and tried to clean the areas as good as possible. Finally I swept everything with cloth dipped in Alkohol. Than I did new fillets. I used a wooden scraper with a slightly bigger rounded end to come around remaining edges that had cured on the surface. When that was done I did the glassing in the two first compartments from bow to stern. It felt good to move on. I finished gluing the rails and attached the „arm“ (can’t remember the english word, sorry) to the rudder.

1 Northeaster Dory: Troubleshooting and a bit more
2 Northeaster Dory: Troubleshooting and a bit more
3 Northeaster Dory: Troubleshooting and a bit more
4 Northeaster Dory: Troubleshooting and a bit more
5 Northeaster Dory: Troubleshooting and a bit more
Glassing & Epoxy · compare · other boats 5 h Link

Glassy Sunday

After a fun night out with Compass Mike, lots of drinks, good music I started the morning with a good breakfast to get my head straight. Starting around noon I finished the glassing on the inside bottom and cut off the fiberglass edges along the masking tape in the first two compartments from the bow to the middle. I am quite happy with the result and allow my self some tiny bumps as it is my first boat building experience. In the evening I glued the first thwart and started the mast thwart with cutting the hole for the mast and adding the rails. I had some thickened epoxy left and not enough screw clamps remaining for a second regular thwart. For the mast thwart there were plenty of spring clamps. It turned out that my jigsaw is pretty worn out so the cutting edge along the bottom line was a little inside. I had to use a rasp to meet the outline.

1 Northeaster Dory: Glassy Sunday
2 Northeaster Dory: Glassy Sunday
3 Northeaster Dory: Glassy Sunday
Glassing & Epoxy · compare · other boats 4 h Link

Glassing

This weekend I was a bit lasy with writing the blog but I worked on the boat. I added the fiberglass to the outside of the hull. First I shaped the bow a bit more than I spread out the fabric and rolled out all the wrinkles and bubbles. The glassing went pretty good!

1 Northeaster Dory: Glassing
2 Northeaster Dory: Glassing
3 Northeaster Dory: Glassing
Glassing & Epoxy · compare · other boats 2.5 h Link

Flea Market instead

After another great night out my alarm clock woke me up at 8:00 am. I planned to get the skeg fixed to the bottom, shape the rails and find the right position for the dagger board hole. I was just able to finish cutting the rest of the fiberglass along the joint of panel one and two. At this moment my daughter showed up and asked if we could go to a flea market. How could I say no. Back from the market I cut off the ends of the rails at the transom and shortend the rail on the bow. I tried to sand of a bit of the left rail as mentioned in the manual, but the belts of the belt sander seem to be old and started breaking exactly at the seams. Running out of sand belts I went fore a run with Mike. Round about 00:00, Mike and I had spent some time at an art galerie, we had a last beer in the kitchen. Afterwards I decided to give the rudder, the mast step and the skeg a third coat. That was the first time I gathered some experience with the foam brush. I am looking forward until the coat is drie. If it stays that shiny, like it was now, that would mean a quite good result. Let’s see if I can get more things done tomorrow.

Others building the Northeaster Dory

The same boat, in somebody else's shop.

All Northeaster Dory logs, with the medians