boatbuildlog

Tiny Titan · new build

Glen L Tiny Titan Hydroplane

by Matt · Texas · Message Matt

Building a small hydroplane for the kids to learn some basic boating skills on a fun boat!

Make a book Feed The whole log, 41 entries and every photo, laid out as a book to print, bind and keep.
41
Entries
68
Hours
76
Days elapsed
203
Photos
Spent
Aug 2026
Started
Hull Exterior · other boats 1 h Link

Okay I finished adding the 1/4 in plywood to the bottom of one of the sides. I used a lot of screws and a lot of thickened epoxy to make sure that it sticks pretty well. I will do the other side in a few days and then once they're both ready I will do a rough sand to get them ready for glassing.

1 Tiny Titan: hull exterior
2 Tiny Titan: hull exterior
Hull Exterior · other boats 1 h Link

Finished gluing on the other bottom plank. Lots and lots and lots of sanding to do, as these are very rough cuts.

1 Tiny Titan: hull exterior
2 Tiny Titan: hull exterior
3 Tiny Titan: hull exterior
Hull Exterior · other boats 1 h Link

Before the sanding

So I'm showing the rough edges on all of the bottom of the hull. As you can see there's lots of mistakes, lots of Gap, lots of overlap, and lots of sanding to do. This will be a multi-day sanding project as I will start with 60 grit or 80 grit on the belt Sander and then work my way to about 120 to 150 grit to prep it for fiberglassing.

1 Tiny Titan: Before the sanding
2 Tiny Titan: Before the sanding
3 Tiny Titan: Before the sanding
4 Tiny Titan: Before the sanding
5 Tiny Titan: Before the sanding
6 Tiny Titan: Before the sanding
Fairing & Sanding · other boats 1.5 h Link

Got a little bit of sanding done today. Today was mostly the rough sanding so I used a belt sander with 80 grit just chopping up the wood. It's pretty smooth all around, there's some areas where I have to fix with more epoxy and then resand but overall it's looking a lot better.

1 Tiny Titan: fairing & sanding
2 Tiny Titan: fairing & sanding
3 Tiny Titan: fairing & sanding
4 Tiny Titan: fairing & sanding
5 Tiny Titan: fairing & sanding
6 Tiny Titan: fairing & sanding
Glassing & Epoxy · other boats 2 h Link

Today I applied the fiberglass to the bottom of the hull. This actually went a lot smoother than I thought it would, but this is like the third boat that I've fiberglassed, so I think I'm finally figuring how to do it correctly.

I'm using a new epoxy and hardener, something different than I've previously used. So far it is more smelly but it seems to be a little bit less thick than the previous one, which makes it pretty runny. Fortunately I was able to squeegee out most of the excess so it actually looks pretty good and I won't have to do a ton of unnecessary sanding.

After this dries I will send everything down and then apply an additional layer of fiberglass tape along the sides of the hall. I also have yet to do the transom, so I will do that at the same time.

1 Tiny Titan: glassing & epoxy
2 Tiny Titan: glassing & epoxy
3 Tiny Titan: glassing & epoxy
4 Tiny Titan: glassing & epoxy
5 Tiny Titan: glassing & epoxy
6 Tiny Titan: glassing & epoxy
7 Tiny Titan: glassing & epoxy
8 Tiny Titan: glassing & epoxy

Nobody else here is logging a Tiny Titan yet. See the boat.

What it cost

$1,966.00
$1,537.00
Into the boat
$429.00
Tools & gear
ItemQtySupplierCost
Boat Plans 1 Glen-L $75.00
Ryobi Plug-in jigsaw 1 Home Depot $100.00
lumber 1 Home Depot $100.00
Fir AB Marine 1/4" 4x8 2 Plywood company $200.00
Fir AB Marine 1/2" 4x8 1 Plywood company $137.00
Birch 1/8 4x8 Plywood 1 Plywood company $35.00
Craftsman planer 1 Home Depot $329.00
Fasteners and Fiberglass kit 1 Glen-L $400.00
6oz Fiberglass Cloth Roll 1 Amazon $15.00
6HP 2 Stroke Hangkai Outboard Engine 1 Hangkai $575.00