boatbuildlog

Northeaster Dory · new build

Northeaster Dory to be assembled in Cologne Germany

It is the first boat I build. I‘ll do it in my single garage and partly in my cellar.

Make a book Feed The whole log, 23 entries and every photo, laid out as a book to print, bind and keep.
23
Entries
121
Hours
32
Days elapsed
65
Photos
Oct 2026
Started
Watch the 30 second boat build video

The film on its own page

Hull Exterior · compare · other boats 6 h Link

Rails for the Dory

It was quite successful cleaning the edges around the transom with my new block plane. I sharpened the blade before I started and it became so sharp that I cut my thumb with a slight touch. Sad to notice that I had to pass some of the copper wires that had to remain in the transom because of the fillets. Now the blade of the block plain has several marks but I will reshape it. The bow got rounded as well and in the Afternoon, when it was quite warm outside my Mother helped me by attaching the first pair of rails. Perfect to work outside with a little more space. To give the rails the right bend at the transom I drilled two wholes to the extra length of the rails, made a loop with copper wire and twisted it to get the right tension.

1 Northeaster Dory: Rails for the Dory
2 Northeaster Dory: Rails for the Dory
3 Northeaster Dory: Rails for the Dory
4 Northeaster Dory: Rails for the Dory
Hull Exterior · compare · other boats 7 h Link

Bullet shape

After 24 hours curing time it was time for the second pair of rails. My Mother is still around so she gave me a hand. It seems ther could have been one too three more screw clamps but it looks ok after a few adjustments. The trickiest spot is about 25“ to the transom. Panel 4 has a slight S-Schape there and it felt hard to meet the line. Besides that I shaped the dagger board which gave me a lot satisfaction. In the evening I coated it with epoxy and it looks nice. There are a few more parts that got brushed with epoxy. A good day of work, mostly outside.

1 Northeaster Dory: Bullet shape
2 Northeaster Dory: Bullet shape
Hull Exterior · compare · other boats 6 h Link

Rails unclamped ready for glassing

Unclamped the rails and gave it quiet a bit of sanding to get the rails smooth and to the same level at every inch. I found some tiny edges down the line but nothing dramatic. With the sander in hand I gave the bow some more shape and cleaned the edges between bottom and panel one. Now it’s ready to get glassing from the outside. In the next step I sanded the rudder in preparation for it’s first coat which I applied in the evening. I borrowed a powerful saw from a neighbor, because mine sucks. This one went through the thwart like through butter. For the long, straight cuts I used my (hand) circular saw, which was good, even without a rail to use the saw with. Now I am confident that I‘ll be able to give the mast the right shape with my circular saw. Before I was wondering if I have to ask a friend if I can use his workshop (he is a framer and has got all the heavy tools).

1 Northeaster Dory: Rails unclamped ready for glassing
2 Northeaster Dory: Rails unclamped ready for glassing
3 Northeaster Dory: Rails unclamped ready for glassing
Glassing & Epoxy · compare · other boats 4 h Link

Glassing

This weekend I was a bit lasy with writing the blog but I worked on the boat. I added the fiberglass to the outside of the hull. First I shaped the bow a bit more than I spread out the fabric and rolled out all the wrinkles and bubbles. The glassing went pretty good!

1 Northeaster Dory: Glassing
2 Northeaster Dory: Glassing
3 Northeaster Dory: Glassing
Hull Exterior · compare · other boats 6 h Link

Carpentry and bubbles

Saturday the dagger board, rudder, mast stepp and dagger box got a second coat. I spent lots of time cutting and sanding two of the thwarts. The third was glued and I cut the three pieces for the seat in the stern. The evening before I decided to increase the temperature of my heater. Before I always used power level 1 so I switched to 2 (of three). When I entered the garage Saturday morning I figured that I should have increased the distance between boat and heater. No worries, I did not burn the boat but the higher temperature caused a few bubbles underneath the glassing. Something to think about especially because the rest of the hull has such a nice surface now.

1 Northeaster Dory: Carpentry and bubbles
2 Northeaster Dory: Carpentry and bubbles
3 Northeaster Dory: Carpentry and bubbles
4 Northeaster Dory: Carpentry and bubbles
5 Northeaster Dory: Carpentry and bubbles
6 Northeaster Dory: Carpentry and bubbles
7 Northeaster Dory: Carpentry and bubbles

Others building the Northeaster Dory

The same boat, in somebody else's shop.

All Northeaster Dory logs, with the medians