Started sanding the first puzzle joints. The once of panel 1 + 2 were quite good. It needed just a little sanding. With the bottom of the hull I got a little trouble. I should have taken better care that every piece of the puzzle fits good together and everything is at the same level. It took me quite a while to sand it all smooth. Especially below the joints was a lot of cured thickened epoxy. Hopefully the picture shows what I am trying to explain.
After sanding I added the bow tips of panels 1 + 2 and attached the stern tips to panels 3 + 4.
Because of limited space I couldn’t do it all in one step.
It took me about 3 hours. In the evening I had a couple of beers with my good friend and owner of „the compass“. I introduced him to the stage I am in now and some of the stuff I bought for the project. Besides that I did a little sanding of the transom and the frames. I decided not to count that (fun) time.
The day started with sanding the remaining joints of panel one and two. The goal was to get started building the hull in the evening together with my older brother. To reach that goal it was necessary to finish gluing all the panel parts. So finally I had to attach the bow panels of panel 3 and 4. I spent about two hours in the morning and let the epoxy cure till the evening.
My brother arrived around 5pm. Before we started working we had a delicious meal. We started at 7:15pm. The epoxy on panel 3 and 4 cured as expected. We removed panels and the table tennis from the garage. The cart was set into place to start the assembly. Taking a closer look at the bottom we noticed that the little holes to set the frames were missing. Because my brother brought his router we decided to drill them. As you can see in the pictures, where all frames are sat in place, we really succeeded.
We worked our way from panel one, to the transom and the right part of panel two until 00:15am (5 hours). From twisting copper wire my fingertips are burning now but the result makes me pretty happy. While we were attaching the frames to panel one we had a phone call from my son. He spends halve a year in Canada for a school exchange program. It was nice to talk to him. And it seems that my daughter had her very first date tonight. Fun fact, the boy told me he can sail and his uncle has a boat too.
My brother and I started working on the hull around 9:30 this morning. We worked our way from panel to panel. Panels 3 & 4 still needed a bit of sanding. Cause this panels are so long we just put them on the floor of the garage for sanding. I kept some of the long cardboard pieces and lined the up on the floor. We gained some speed with copper wire. Now that we are good at it there is no more such work left. After retwisting every single wire with pliers, we were able to flip the hull. Upside down we had to fix some more wood to the cart to extend its width so the hull can easy rest on it. But that was not a big deal. I am really happy that the complete boat still fits into the garage. If I hafe to work with closed doors I have to crawl underneath to get to the other side. This way I am able to keep it dry and worm. That’s worth it. After a coffee break I had my first experience with filling the gap between the bottom and panel 1. The pastry bag did a great job. It worked well, easier than I expected. Tomorrow I have to seal the gaps between all the panels. The gaps at the bow between 2&3 are quite not existing. Any suggestions? I thought about loosening the wires and putting toothpicks between the panels to open the gap.
I used some spacers, a carpenter once gave me, to level the base of my terras, to open the gap at the bow end of panel 1.. Working with the pastry bag was a good experience. When I am done with the Dory I am ready for some nice cake! It was kind of tricky to hit the right mixture of thickened epoxy. At the end I got pretty good at it. After each panel I glued I took a look to the inside and just found very few running epoxy. Of course I thought I could work that good, that not a single wire has to remain in the hull - guess what - I didn’t manage that. I did one batch with about 300ml in one pastry bag. That was kind of hard to handle. I recommend a maximum of around 200ml per bag. That allows you to twist the end of the bag and give it a knot (a plastic clip from the kitchen could work as well) Barely forgot to tell that I found around 50ml of the 300ml batch on my shoe after I stopped holding the end of the bag that was just twisted. I guess I needed the hand to stop some running epoxy - can’t remember. Now my Redwing Shoe is watertight forever.
Not to much done today. I pulled out all the wires. Only the once in the bow, the bulkheads and the transom remain. With the help of my wife and Liz we turned the hull around again. I had to sand only this tiny area in the stern. The rest was all good on the inside. Before I didn’t have time and clamps to glue other parts so I did the skeg, the dagger board and the rudder today. The masking tape is attached an I measured and cut the fiberglass cloth. I‘d say all of this took me 4 hours. Ahh forgot to tell that I had to buy more sanding paper (80 grid) and more brushes.